Rotary Dryer Design PDF
Get Latest PricePayment Type: | L/C,T/T,D/P,Paypal,Money Gram,Western Union |
Incoterm: | FOB,CFR,CIF,EXW,FCA,CPT,CIP |
Min. Order: | 1 Set/Sets |
Transportation: | Ocean,Land |
Port: | Qingdao,Shanghai,Tianjin |
Payment Type: | L/C,T/T,D/P,Paypal,Money Gram,Western Union |
Incoterm: | FOB,CFR,CIF,EXW,FCA,CPT,CIP |
Min. Order: | 1 Set/Sets |
Transportation: | Ocean,Land |
Port: | Qingdao,Shanghai,Tianjin |
Model No.: GHG2×18
Brand: Kingoro
Material Status: Power
Drying Medium: Air
Movement Way: Agitation
Heating Mode: Transmission
Operation Pressure: Atmospheric Pressure
Drum Number: Single
Type: Top-Feed Type
Certification: CE ISO SGS
Motor: Siemens Brand
Weight: 13 T
Voltage And Frequency: 380V/50HZ, 3Phase
Application: Drying For Sawdust
Selling Units | : | Set/Sets |
Package Type | : | Export Package |
Working Principle and Main Structure:
1. The drying body is composed of cylinder body, ring gear and rolling ring. The drying body is on the tug rolling device and block rolling device supported by front and back rolling ring. It can control axial direction traversing of drying body by adjusting tug rolling device and block rolling device. The driving device drives drying body rotating through the ring gear. Electric motor (frequent) as the power can achieve stepless speed adjusting and meet the demand of different rotating speed. The driving has two forms, left driving and right driving. Method of distinction: look at from the direction of inlet, the driving device that is at the left side of drying body is left driving; the driving device that is at the right side of drying body is right driving.
2. The sealing of air inhale device adopts floating sealing structure. This structure can ensure the air inhale efficiency; there is sealing device at the end of drying body, which can prevent cold air go to inner of dryer; there is feeding exhaust air hood, and exhaust material hood, which can prevent the evaporated water vapor and discharge dust pollute the working environment.
3. The material is feed into cylinder body, and pushed to lifting plate by material leading screw. Due to the tilt and rotating of drying body, the material is raised and scattered along circumferential direction, and meanwhile run longitudinal movement in the cylinder body; high temperature medium (hot smoke gas) fold to outer exhaust flue through rotary drying body and tail pipe. Material and high temperature medium do heat exchange by heat conduction and radiation way to evaporate the water of material, and then achieve drying the material.
Industrial Efficient Rotary Dryer is made up of a large, rotating cylindrical tube, usually supported by concrete columns or steel beams. The dryer slopes slightly so that the discharge end is lower than the material feed end in order to convey the material through the dryer under gravity. Material to be dried enters the dryer, and as the dryer rotates, the material is lifted up by a series of internal fins lining the inner wall of the dryer. When Industrial Efficient Rotary Dryer gets high enough to roll back off the fins, it falls back down to the bottom of the dryer, passing through the hot gas stream as it falls. This gas stream can either be moving toward the discharge end from the feed end (known as co-current flow), or toward the feed end from the discharge end (known as counter-current flow). The gas stream can be made up of a mixture of air and combustion gases from a burner, in which case the dryer is called a direct heated dryer. Alternatively, the gas stream may consist of air or another (sometimes inert) gas that is preheated. When the gas stream is preheated by some means where burner combustion gases do not enter the dryer, the dryer known as an indirect-heated type. Often, indirect heated dryers are used when product contamination is a concern. In some cases, a combination of direct-indirect heated rotary dryers are also available to improve the overall efficiency.
Applicable raw Material:
Saw dust, rice husk, organic fertilizer whose moisture rate is high, as well as some chemical products, foundry sand, medical products and mixed coal.
Parameter:
Model Evaporation (t/h)
Power (kw)
GHG1.2X12 0.27-0.3 5.5 GHG1.5X15
0.53-0.58 11 GHG1.6X16 0.6-0.66 11 GHG1.8X18 0.92-1.01 15 GHG2X18 1.13-1.24 15 GHG2X24 1.55-1.66 18.5 GHG2.5X18 1.77-1.94 22
Packing And Shipping:
Our service:
1) 24 hours online service.
2) All-the-way tracking service offered from placing order to delivery.
3) Free training for operation, debugging and daily maintenance.
4) We can provide professional guide installation.
5) One year warranty and all-round after-sales service.
6) Customized design and flow chart are available for our clients.
7) Independent R&D team and strict & scientific management system.Drum Rotary Machine For Biomass SawdustDrum Rotary Machine For Biomass Sawdust
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.
Fill in more information so that we can get in touch with you faster
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.